Call 08048981260 91% Response Rate

our range

Logic Programmers and Converters

Offering you a complete choice of products which include pickit 3 debugger programmer, drv8833 2 channel dc motor driver module board 1.5a 3v-10v (red), pwm dc motor controller module, cp2102 usb to u art converters, cp2102 usb to ttl converters and pl2303 usb ttl converter module.
Pickit 3 Debugger Programmer

Pickit 3 Debugger Programmer

Rs 1,250  / PieceGet Best Price
MaterialPROGRAMMER
Weight0.12 kg
Single package size11 x 5 x 2 cm
Voltage Range2.0 V to 6.0 V
Speed12 Mbits
Packaging TypeBox
This is PICkit3 Debugger Programmer Emulator Controller Development board w/ Pinout diagram to ease the customer. The USB connection is more stable than ICD2.

PICKIT3.5, begin to support Win7 system. Full patch design, patch through the reflow soldering processing, more stable quality. PIC developing data, C language development tool manual. A lot of PIC basic experiment program code; ICD2 PICKIT3 etc application specification.

The MPLAB PICkit 3 allows debugging and programming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineers PC using a full-speed USB interface and can connect to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).

 


Features of PICkit3 Debugger Programmer Emulator Controller Development Board:
  • Full-speed USB support using Windows standard drivers
  • Real-time execution
  • Processors run at maximum speeds
  • Built-in over-voltage/short circuit monitor
  • Low voltage to 5V (1.8 to the 5V range)
  • Read/write program and data memory of the microcontroller
  • Diagnostic LEDs (power, active, status)
  • Read/write program and data memory of the microcontroller
  • 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
  • Peripheral freeze at the breakpoint.
  • Program up to 512K byte flash.

Specifications of PICkit3 Debugger Programmer Emulator Controller Development Board:-
Input Supply voltage (V)

     1.8 ~ 5

Flash Memory (Kbytes)

      512

Dimensions of PicKit3

      As per below

Length (mm)

      95

Width (mm) 

      40

Height (mm)

      11.5

Weight (gm)

      30



Package Includes :

 

  • 1 x PICKIT3 Programmer.
  • 1 x USB cable
  • 1x 6pin cable

View Complete details

get quote request a call back
  • DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)
  • DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)
  • DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)
  • DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)
DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)

DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)

Rs 160  / PieceGet Best Price
Mfr. Part NumberDRV8833
Motor TypeDC MOTOR
BrandCHINA

DRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 V to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. The board ships populated with SMD components, including the DRV8833, and adds an FET for reverse battery protection.

The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.


FEATURES:
  1. Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
  2. Operating voltage: 2.7‌‌ V to 10.8 V
  3. Output current: 1.2 A continuous (2 A peak) per motor
  4. Motor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor
  5. Inputs are 3V- and 5V-compatible
  6. Under-voltage lockout and protection against over-current and over-temperature
  7. Reverse-voltage protection circuit
  8. Current limiting can be enabled by adding sense resistors (not included)

View Complete details

get quote request a call back
PWM DC Motor Controller Module

PWM DC Motor Controller Module

Rs 100  / PieceGet Best Price
Input Voltage24Volts
Power600mA
Weight28g
Packaging TypeBox
Storage Temperature-25 Degree C ~ +130 Degree C

View Complete details

get quote request a call back
CP2102 USB To U ART Converters

CP2102 USB To U ART Converters

Rs 150  / PieceGet Best Price
Usage/ApplicationARDUINO
PhaseSingle Phase
Temperature-20 to 70 Degree C
Speed300Bps
Packaging TypeBox
Number of Pin6

This is the CP2102(6-pin) USB 2.0 to TTL UART serial converter module. This is a great little tool for embedded systems that require a serial connection to a computer. The board can simply attach to a USB bus and will appear as a standard COM port.

ThisCP2102 doesn't require any external oscillator, it onboard-board voltage regulator, and it even uses a reprogrammable internal EEPROM for the device description. The full hardware UART has flow control for baud rates from 300bps to 921600bps.

This breakout also allows you to connect the TX/RX pins of your favorite microcontroller or serial application to the RX/TX pins of the breakout, creating a simple serial cable replacement.


Supported operating systems

 

Windows 98/Me/2000/7MAC OS-9MAC OSX-Windows CELinux 2.40 or later

 


Features :
  1. Brand new and high quality
  2. Included USB transceiver, without external circuit device
  3. Includes a clock circuit and power-on reset circuit
  4. With 3.3V and 5V dual power output
  5. With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status
  6. Meet the USB2.0 specification requirements
  7. SUSPEND pin supports USB suspend state
  8. With self-recovery fuse. In the event of the accidental short circuit, it can effectively protect your computer USB port and Downloader
  9. With reset signal output, etc. directly to the Arduino board Promini download!
  10. Asynchronous serial data bus compatible with all handshake and modulation controller interface signals
  11. The supported data format is 8 data bits, 1 stop bit and parity bits
  12. Connotation 512 byte receive buffer and 512 bytes transmit buffer
  13. Supports hardware handshaking or X-ON/X-OFF

View Complete details

get quote request a call back
CP2102 USB to TTL Converters

CP2102 USB to TTL Converters

Rs 175  / PieceGet Best Price

Minimum Order Quantity: 25 Piece

Usage/ApplicationARDUINO
BrandCHINA
Length2.6 cm
Weight10g
Temperature0 to 55 Degree C
Packaging TypeBox
Number of Pin6

This is the CP2102(6-pin) USB 2.0 to TTL UART serial converter module. This is a great little tool for embedded systems that require a serial connection to a computer. The board can simply attach to a USB bus and will appear as a standard COM port.

ThisCP2102 doesn't require any external oscillator, it onboard-board voltage regulator, and it even uses a reprogrammable internal EEPROM for the device description. The full hardware UART has flow control for baud rates from 300bps to 921600bps.

This breakout also allows you to connect the TX/RX pins of your favorite microcontroller or serial application to the RX/TX pins of the breakout, creating a simple serial cable replacement.


Supported operating systems

 

Windows 98/Me/2000/7MAC OS-9MAC OSX-Windows CELinux 2.40 or later

 


Features :
  1. Brand new and high quality
  2. Included USB transceiver, without external circuit device
  3. Includes a clock circuit and power-on reset circuit
  4. With 3.3V and 5V dual power output
  5. With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status
  6. Meet the USB2.0 specification requirements
  7. SUSPEND pin supports USB suspend state
  8. With self-recovery fuse. In the event of the accidental short circuit, it can effectively protect your computer USB port and Downloader
  9. With reset signal output, etc. directly to the Arduino board Promini download!
  10. Asynchronous serial data bus compatible with all handshake and modulation controller interface signals
  11. The supported data format is 8 data bits, 1 stop bit and parity bits
  12. Connotation 512 byte receive buffer and 512 bytes transmit buffer
  13. Supports hardware handshaking or X-ON/X-OFF

Package Includes :1 x CP2102(6-pin) USB 2.0 to TTL UART serial converter module

Specifications :-
Length (mm)            

42

Width (mm)

16

Height (mm)

6

Weight (gm)

4

View Complete details

get quote request a call back
PL2303 USB TTL Converter Module

PL2303 USB TTL Converter Module

Rs 100  / PieceGet Best Price
Model Name/NumberPL2303
Usage/ApplicationARDUINO
BrandCHINA
Dimensions62.8mm x 33.8mm x 17.8mm
Voltage3.3V to 5V
Weight0.06 kg
Size29 mm x 17 mm
Packaging TypeBox

PL2303 - PL2303HX USB to TTL Serial UART Converter Module is a handy, low cost module. Adopt imported controller RS232 TTL, which can stabilize the flash with high-speed 500mA self-recovery fuse for protection.

Two data transmission indicator can monitor data transfer status in real time. Reserve 3.3V and 5V pin interface, easy for DDWRT of different voltage system that needs power. The entire board is coated by a high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside, so that the board won’t be burnt down by a material shortcut.


Applications of PL2303 USB to TTL USB Converter Module:-

 

  • All kinds of satellites set-top box upgrade
  • Router, HDD, ADSL, broadband modem firmware upgrade or cracked upgrade
  • cellphone, XBOX360, GPS serial communication, vehicle inspection and test, DVD flash and so on
  • Burn write STC MCU, NXP MCU, Renesas MCU, NEC MCU and so on
  • Simple UART communication commonly used UART debugging tools in supper terminal
  • USB signal transferred to TTL signal may be used by electronic enthusiasts

 


Features of PL2303 USB to TTL USB Converter Module:- 

 

  • Adopt imported controller PL2303HX, which can stabilize the flash with high speed
  • 500mA self-recovery fuse for protection
  • Two data transmission indicator can monitor data transfer status in real time
  • Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power
  • The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside,
  • so that the board won’t be burnt down by material shortcut.
  • Electrostatic package ensures the board will not be damaged before use
  • Excellent driver support--drivers are available for Windows 98 to Windows 7 (32 bit and 64 bit), Mac OS 8 to OS X (32 bit and 64 bit) and Linux. Even Android is supported!

View Complete details

get quote request a call back
RS232 To RS485 Module

RS232 To RS485 Module

Rs 50  / PieceGet Best Price
Usage/ApplicationElectronics
Speed300 to 115000 bps
Weight200g
Humidity5% to 95%
Dimensions85 x 54 x 25 mm
Packaging TypeBox
The MAX485 TTL To RS485 Module converts TTL signal to RS485 for long range, high data rate error prone differential communication. Digital communications networks implementing the EIA-485 standard can be used effectively over long distances and in electrically noisy environments.

Multiple receivers may be connected to such a network in a linear, multi-drop configuration. These characteristics make such networks useful in industrial environments and similar applications.

This converter lets you send and receive data using the RS485 network from your Arduino/microcontroller. Similar to Serial TTL and RS232 interfaces, the RS485 lets you transfer data between microcontrollers and devices but with extra features! RS485 is an industry standard protocol for data transfer and provides numerous advantages.

It lets you transfer data between up to 32 devices, through the same data line over a cable length of up to 1.2km (4000ft) with a maximum data rate of 10Mbit/s. This converter is designed for office and industrial applications (non-isolated) and provides superior characteristics/features normally found only on more expensive units.


Features of MAX485 TTL to RS485 Converter Module :-
  1. On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
  2. A low power consumption for the RS-485 communication
  3. Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
  4. Slew-rate limited transceiver
  5. All pins of the chip have been lead to can be controlled through the microcontroller.
  6. Convenient RS-485 communication wiring
  7. Multiple Units can be connected to the same RS-485 bus wiring.
  8. All Chip pins are brought out for proper controls


Specifications of MAX485 TTL to RS485 Converter Module:-
IC Chip

MAX485

Operating Voltage (VDC)    

5

Length (mm)

45

Width (mm)

15

Height (mm)

14

Weight (gm)

4

View Complete details

get quote request a call back
FT232 USB To TTL Converters

FT232 USB To TTL Converters

Rs 200  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

Model Name/NumberFT232
Usage/ApplicationARDUINO
BrandCHINA
Weight0.079 kg
UseMP3 / MP4 Player,Video Game Player, Camera, Mobile Phone
Packaging TypeBox
Single Package size2 x 3 x 2 cm

This is USB to TTL 3.3V 5.5V  Serial Adapter Module based on FT232RL IC, It is mainly used for arduino applications.

Features of FT232RL IC:-

 

  • Single chip USB to asynchronous serial data transfer interface.
  • Entire USB protocol handled on the chip. No USB specific firmware programming required.
  • Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
  • Fully integrated USB termination resistors.
  • Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
  • Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
  • 128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.

 


Features of FT232RL USB TO TTL Module:-

 

  • Material: PCB + Electronic Component
  • Support 3.3V, 5V
  • Main Color: Red
  • Chipset: FT232RL
  • USB power has over current protection, using 500MA self-restore fuse
  • RXD/TXD transceiver communication indicator
  • Pin definition: DTR,RXD,TX,VCC,CTS,GND
  • Pitch:2.54mm
  • Module Size: About 36mm(length)*17.5mm(width)
  • Interface : Mini USB

View Complete details

get quote request a call back
MAX485 To RS485 TTL Converter

MAX485 To RS485 TTL Converter

Price on Request
Usage/ApplicationARDUINO
Model Name/NumberMax 485
Dimensions63mm x 35mm x 17mm
Operating Temperature-40 to 85 Degree C
Packaging TypeBox
Supply Ability500 Unit
The MAX485 TTL To RS485 Module converts TTL signal to RS485 for long range, high data rate error prone differential communication. Digital communications networks implementing the EIA-485 standard can be used effectively over long distances and in electrically noisy environments.

Multiple receivers may be connected to such a network in a linear, multi-drop configuration. These characteristics make such networks useful in industrial environments and similar applications.

This converter lets you send and receive data using the RS485 network from your Arduino/microcontroller. Similar to Serial TTL and RS232 interfaces, the RS485 lets you transfer data between microcontrollers and devices but with extra features! RS485 is an industry standard protocol for data transfer and provides numerous advantages.

It lets you transfer data between up to 32 devices, through the same data line over a cable length of up to 1.2km (4000ft) with a maximum data rate of 10Mbit/s. This converter is designed for office and industrial applications (non-isolated) and provides superior characteristics/features normally found only on more expensive units.


Features of MAX485 TTL to RS485 Converter Module :-
  1. On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
  2. A low power consumption for the RS-485 communication
  3. Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
  4. Slew-rate limited transceiver
  5. All pins of the chip have been lead to can be controlled through the microcontroller.
  6. Convenient RS-485 communication wiring
  7. Multiple Units can be connected to the same RS-485 bus wiring.
  8. All Chip pins are brought out for proper controls


Specifications of MAX485 TTL to RS485 Converter Module:-
IC Chip

MAX485

Operating Voltage (VDC)    

5

Length (mm)

45

Width (mm)

15

Height (mm)

14

Weight (gm)

4


 

Package Includes:-

1 x MAX485 TTL to RS485 Converter Module

View Complete details

get quote request a call back
MAX232 TTL Converter

MAX232 TTL Converter

Price on Request
Usage/ApplicationElectronics
Current TypeDC
Weight18.0 grams
Supply Voltage3.3V-5.5V
Operating Temperature-40~+85 Degree C
Model NumberMAX232
Transmission distance2 km

The RS232 Board is used for establishing RS232 communication with devices powered from 3V 5.5V. It contains SP3232 (RS-232 Transceiver) and DB9 connector used for connecting PC and MCU. The RS232 Board features ESD protection and supports hardware flow control.

The SP3222E/3232E series is an RS-232 transceiver solution intended for portable or handheld applications such as notebook or palmtop computers. The SP3222E/3232E series has a high-efficiency, charge-pump power supply that requires only 0.1F capacitors in 3.3V operation. This charge pump allows the SP3222E/3232E series to deliver true RS-232 performance from a single power supply ranging from +3.3V to +5.0V.


Features:
  1. SP3232(RS232)
  2. DB9 connector
  3. UART port

Package Includes:

1 x RS232 to TTL SP3232 UART Transceiver Communication Serial Module

1 x 6-pin custom connector jumper wire



Specifications :-
IC Chip

SP3232E

Operating Voltage                

DC 3.0~5.5 V

Length (mm)

45

Width (mm)

25

Height (mm)

2

Weight (gm)

18

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES