Call 08048981260 79% Response Rate

our range

New Items

USB ASP AVR Programmer for ATMEL Processors

USB ASP AVR Programmer for ATMEL Processors

Rs 150  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

BrandCHINA
Usage/ApplicationElectronics
Mounting TypeSMD
Part NumberUSB ASP PROGRAMMER
TypeLeaded
I Deal InNew Only
Weight25g
Dimensions7.5 x 3.5 x 0.2 cm and 8.5 x 5.7 x 2cm
Power5 V
Packaging TypeBox
Operating Temperature0 to 55 Degree C

The USB ASP AVR Programming Device for ATMEL processors is a USB in-circuit programmer for Atmel AVR controllers. USB ASP AVR Programming Device for ATMEL Processors simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver; no special USB controller is needed.


Specifications and Features :
  1. Model No.: USB ASP AVR Programming Device for ATMEL Processors
  2. Compatible Chips:
    1. ATMega Series
    2. Tiny Series
    3. Classic Series
    4. CAN Series
    5. PWM Series

Package Includes :

1 x USB ASP AVR Programming Device.

1 x FRC cable.

 



Specifications :-
Model no

USBASP AVR Programmer

Length (mm)              

63.3

Width (mm)

20.5

Height (mm)

10.5

Weight (gm)

15

View Complete details

get quote request a call back
Jumper Wire Male To male 40mm Dunpot

Jumper Wire Male To male 40mm Dunpot

Rs 50  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

ColorMIX COLOUR
Current1 Amp
VoltageDC 12 V
Rated Pressure25 kPA
Cable Length20 cm - 8 inch
Weight30 gm

This is Male To Male Jumper Wires (10cm) - 40 Pieces pack. A very Flexible and easily detachable cable to the no. of wires according to your requirement. It has 1Pin male to the 1pin male header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers.

This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a bread board or other prototype or test circuit, internally or with other equipment or components, without soldering.

Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connect or of a circuit board, or a piece of test equipment.

Mostly it is useful with Banana Pi, Raspberry Pi, Arduino, and other mini pc and development board. It is very useful in the PCB project, pc motherboard, as well as Breadboard connections. Additionally, it allows you to plug and unplug easily for prototyping and can be used over and over again.


Features :
  1. Compatible with 2.54mm spacing pin headers
  2. 40pcs chromatic colour jump wire
  3. High quality and in good working condition
  4. Durable and reusable
  5. Easy to install and use
  6. A popular choice for construction or repair
  7. Be used for the electronic project and Genuine Arduino product
  8. Flexible Breadboard Jumper Cable Wire allows you to plug and unplug easily for prototyping.

Package includes :

1 x Male To Male Jumper Wires (10cm) - 40 Pieces pack



Specifications :-
Cable Type                             

Male to Male

Length (mm)

100

Weight (gm)

25



View Complete details

get quote request a call back
2 Channel 5V Relay Module with Optocoupler

2 Channel 5V Relay Module with Optocoupler

Rs 75  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

BrandSingle
Number of Channel2 Channel
AC VoltageAC 125 V- 250 V
DC VoltageDC 28 V- 30 V
AC Current10 A

This is a 5V, 10A 2-Channel Relay interface board. It can be used to control various appliances, and other equipments with large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

It has a 1x4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays.

 

The pins are marked on the PCB:-

 

  • GND - Connect 0V to this pin.
  • IN1 - Controls relay 1, active Low Relay will turn on when this input goes below about 2.0V
  • IN2 - Controls relay 2, active Low Relay will turn on when this input goes below about 2.0V
  • VCC - Connect 5V to this pin. Is used to power the opto couplers

 

Specification:-

 

  • High current relay, AC250V 10A, DC5V 10A
  • 2 LEDs to indicate when relays are on
  • Works with logic level signals from 3.3V or 5V devices
  • Opto isolation circuitry

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES