Call 08048981260 90% Response Rate

our range

Relay Modules and Sensors

Pioneers in the industry, we offer single channel relay module, tec12706 cooler peltier sensor, sensor module, xh-m602 lixthium battery charging control module overcharge protection module and gravity analog turbidity sensor from India.
Single Channel Relay Module

Single Channel Relay Module

Rs 65  / PieceGet Best Price

Minimum Order Quantity: 100 Piece

Channels1
Model Name/NumberSRD-05VDC-SL-C
MaterialPCB
BrandSongle
Relay Current10A
Input VoltageAC 125-250V
Output VoltageDC 30V
Trigger VoltageDC 5V
Drill Holes3 mm
IsolationOptical isolation at input signal

This is 1 Channel 5V Relay Board Module For Arduino PIC AVR DSP ARM. A wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on can control it.

Each one needs 15mA - 20mA driver current and Equipped with high current relay: DC 5V / 10A, AC 250V / 10A

Standard interface that can be compatible with microcontroller.


Specification and Features :-

 

  • 1 channel relay board
  • Operating Voltage 5V
  • Max Current : 20mA
  • Relay Contact Current Capacity at AC250V: 10A
  • Relay Contact Current Capacity at DC5V: 10A
  • One normally closed contact and one normally open contact
  • Triode drive, increasing relay coil
  • High impedance controller pin
  • Pull-down circuit for avoidance of malfunction
  • Power supply indicator lamp
  • Control indicator lamp
  • Indicator for Relay output status
  • Can Be controlled various appliances & other Equipment With Large current.
  • Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
  • The module is compliant with international safety standards, control and load areas isolation trenches;

 

* Product Images are shown for illustrative purposes only and may differ from actual product.



Additional Information:

  • Production Capacity: EX STOCK
  • Delivery Time: EX STOCK
  • Packaging Details: 100PC BAG

View Complete details

get quote request a call back
  • TEC12706 Cooler Peltier Sensor
  • TEC12706 Cooler Peltier Sensor
  • TEC12706 Cooler Peltier Sensor
  • TEC12706 Cooler Peltier Sensor
TEC12706 Cooler Peltier Sensor

TEC12706 Cooler Peltier Sensor

Rs 125  / PieceGet Best Price

Minimum Order Quantity: 6 Piece

Product Brochure

Hot Side Temperature25 degree C /50 degree C
Max Q50 / 57 Watts
Imax6.4 Amps
Max V14.4 / 16.4 V
Module Resistance1.98 / 2.30 Ohms

Thermoelectric Cooler 6A Peltier Module is the simple application of Peltier Thermoelectric Effect. 

Features:

  • Thermoelectric coolers also are known as TEC or Peltier Module create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. You can also take advantage of a temperature differential to generate electricity.
  • This Peltier works very well as long as you remove the heat from the hot side. After turning on the device, the hot side will heat quickly, the cold side will cool quickly. 
  • If you do not remove the heat from the hot side (with a heat sink or other device), the Peltier will quickly reach stasis and do nothing. We recommend using an old computer CPU heatsink or another block of metal to pull heat from the hot side. 
  • We were able to use a computer power supply and CPU heatsink to make the cold side so uncomfortable we could not hold our finger to it.
  • A thermoelectric cooling (TEC) module is a semiconductor-based electronic component that functions as a small heat pump. 
  • By applying the DC power source to a TEC, heat will be transferred from one side of the module to the other. 
  • It creates a cold and hot side. They are widely used in industrial areas, for example, computer CPU, CCDs, portable refrigerators, medical instruments, and so on.
  • Also Known as Thermoelectric cooling modules, Thermoelectric modules, Peltier modules, Thermoelectric cooling module.
  • Do not exceed Imax or Vmax when operating module.
  • Please carry out moisture protection options (sealing) in final application use.


Additional Information:

  • Delivery Time: EX STOCK
  • Packaging Details: 60PC TRAY

View Complete details

get quote request a call back
Sensor Module

Sensor Module

Rs 100  / PieceGet Best Price
ModelMQ-8
Power Consumption150 mA
Storage HumidityLess than 95%Rh
Operating Voltage4.5-20 V DC
Detecting concentration100-10000 ppm
Preheat time24 hour
Get best price MQ-8 Sensor Module,we are the leading supplier and dealer in MQ-8 Sensor Module

View Complete details

get quote request a call back
Xh-m602 LiXthium Battery Charging Control Module Overcharge Protection Module

Xh-m602 LiXthium Battery Charging Control Module Overcharge Protection Module

Rs 599  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

 This Product is available in two different variant (XH-M602 and HCW-M633) with same working we will ship it randomlyThis XH-M602 Digital Battery Charging Control Module is used to charge batteries. The module has an input terminal for the 220V AC and an output terminal connected through an onboard relay. The module can actively monitor the battery voltage through the Vin terminal and disable the 220V output connected to the battery charger when the battery is fully charged.

Features:
  1.  XH-M602 High-quality screw terminals are suitable for various wiring requirements. 
  2. A plastic transformer which provides corrosion, moisture, rust resistance, high safety factor.
  3. The good quality seven-segment display with the accuracy of 0.1
  4. The module can monitor real-time battery voltage.
  5. According to the set value to start and stop, the board can disconnect input to the battery charger effectively protecting the battery from damage due to loss of power or overcharge.

Package Includes:

1 x XH-M602 / HCW-M633 Digital Battery Charging Control Module

View Complete details

get quote request a call back
Gravity Analog Turbidity Sensor

Gravity Analog Turbidity Sensor

Rs 850  / PieceGet Best Price
BrandCHINA
MaterialPlastic
Operating Current Maximum30 mA
VoltageDC 5 V
Operating Temperature-30 degree C to 80 degree C
Response TimeLess than 500 ms

This is a Turbidity Sensor with Module, an electronic monitoring module specially developed to work with microcontroller platforms Arduino, Raspberry Pi, PIC, ARM, AVR, among others.

It is very efficient, the Arduino Turbidity Sensor is able to detect and verify the quality of the water, making the turbidity measurement, where it is possible to verify the results by means of digital or analog signal next to the corresponding pins in the accompanying electronic module.

The Turbidity Sensor emits at its end an infrared light, imperceptible to human vision, capable of detecting particles that are suspended in water, measuring the light transmittance and the dispersion rate, which changes according to the Amount of TSS (Total Suspended Solids), increasing the turbidity of the liquid whenever levels increase.

In general, the Arduino Turbidity Sensor is applied in projects involving the monitoring of water turbidity in rivers, streams, lakes, water bodies, catchment and research sites, laboratories, tanks with liquids and so on. This Turbidity Sensor has an end specially prepared for direct contact, having an electronic module to amplify and send the received data to the microcontroller of the project


Theory of Operation

The sensor operates on the principle that when the light is passed through a sample of water, the amount of light transmitted through the sample is dependent on the amount of soil in the water. As the soil level increases, the amount of transmitted light decreases. The turbidity sensor measures the amount of transmitted light to determine the turbidity of the wash water. These turbidity measurements are sent to the dishwasher controller, which makes decisions on how long to wash in all the cycles.

These decisions are made on the basis of a comparison between clean water measurements (taken at the beginning of the wash cycle) and the wash water turbidity measurement taken at the end of each wash cycle. By measuring the turbidity of the wash water, the dishwasher can conserve energy on lightly soiled loads by only washing as long as necessary. This will result in energy savings for the consumer.

 
Features :
  1. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc.
  2. Measures turbidity of water in rivers.
  3. Detects and verifies water quality.
  4. Digital and analog output;
  5. Able to detect particles that are suspended in water.
  6. Trimpot for sensitivity adjustment.
  7. Ideal monitoring of water turbidity in rivers, streams, lakes, water boxes, catchment and research sites, laboratories, tanks with liquids and etc.
  8. Comes with module and jumpers

Package Includes :

1 x Turbidity Sensor with Module.

1 x Connecting Cable.


Specifications :-
Working voltage

DC 5V

Working current

30mA [MAX]

Response time

<500 msec

Insulation Resistance

100M [Min]

Operating Temperature (C)

-30 ~ +80

Length (mm)

33

Width (mm)

20

Height (mm)

12

Weight (gm)

55

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES